DNV-GL Type Approval

Choose variant

8 Variants

Side-Power PROportional


A PROportional speed controlled thruster system allows for more precise handling of the boat in all conditions, applying only the necessary power needed to complete your maneuver confidently. By limiting the power under normal weather conditions, noise levels are significantly reduced.

The system also includes a practical HOLD-function in a twin thruster system. With a single press of a button, the bow and stern thruster will keep you alongside the docks - making single handed docking very easy indeed! Proportional thrusters are also the best choice for joystick interaction.

Side-Power S-link™


S-link™ is a CAN-based control system with full intelligent communication between all units in the system, much like a computer network.

  • Round, compact and waterproof connectors with unique keying and color coding to avoid faulty hookup
  • Unlimited number of commands or information transferred on a single cable
  • User feedback at panel
  • Intelligent troubleshooting

Side-Power Q-prop™


The new 5 blade special skew propellers are the result of over 2 years of development work and thousands of tests. They have been designed to reduce the noise level, while maintaining the exceptional efficiency of the old 4 blade Side-Power propellers. This goal was achieved, and we even chose to make them a little bit more aggressive on some models, increasing the thrust on some thrusters about 5%. Please see individual information on each new thruster for more details.

  • Noise reductions of up to 75% measured in controlled environments
  • The expected and tested normal noise reduction in average installations: 20-40%
  • Will be delivered on all Side-Power models except models with 300mm and 385mm tunnel diameter
  • Upgrade kits are available for most SP series thrusters with special adaptors

Side-Power Twin Counter-Rotating

Twin Counter-Rotating Propellers

Two counter-rotating propellers can give the most thrust at a good performance ratio in a minimal tunnel diameter. This system is used in our larger thrusters for maximum power. The TC models are the favourite thrusters among leading boatbuilders for their high-end yachts.

Side-Power Gravity Feed Lubrication

External oil tank for easy access

The thruster gearleg is filled with oil from a remote reservoir located above the waterline. This generates overpressure, making an effective seal against water intrusion in the gear leg.

  • Separate oil reservoir placed above the waterline
  • Allows easy access for oil changes
  • Having the advantage to be able to change oil in units used commercially, with hundreds of running hours per year
Thrust up to (kg • lbs) 1000 • 2205
Typical boat size (ft • m) 100' - 150' • 30 - 45
Tunnel I.D. (mm • in) 513 • 20
Propulsion system Twin Counter-Rotating
Hydraulic power up to (kW • hp) 59.8 • 80.2
Weight (kg • lbs) 146.5 • 323
Item Code SH1000/513-xxx

Weight stated include thruster, props and bellhousing ONLY.

Weight of hydraulic motor (typical 25 - 40 kg) comes in addition.

Measurements Bow Thruster

Measurements Bow Thruster SH1000/513
A (mm • in) 513 • 20.2"
B min (mm • in) 483 • 19.1"
B max (mm • in) 510 • 20"
C min (mm • in) 770 • 30.31"
D min (mm • in) 580 • 22.83"
D recommended (mm • in) 710 • 27.95"
E min (mm • in) 12 • 0.47"
E max (mm • in) 22 • 0.87"

Measurements Stern Thruster

Measurements Stern Thruster SH1000/513
F (mm • in) 405 • 15.94"
G (mm • in) 705 • 28.6"
C min (mm • in) 770 • 27.75"
H max (mm • in) 120 • 4.72"
Tunnel length (mm • in) 850 • 33.46"
Stern thruster kit 91000
Cowls - short model -
Cowls - long model -
# Description Product
1 Propeller 70 1270 LH
1b Propeller 70 1270 RH
2 Propeller key 70 1242
3 Propeller washer LSD-45
4 Locknut PM 45
5 Anode Zink 70 1180
5b Anode Alu 70 1180 A
6 Oil drain screw with gasket 50 1220
7 Gasket (between gearleg and tunnel) 70 1312
8 Gearleg bolt 70 1080
9 Gearleg washer plate 70 1241
10 Nut 21203
11 Drive shaft key 70 1244
12 Complete gearleg w/props 70 0601
12b Complete gearleg without props 70 0600
12c Complete gearleg remanufactured 70 0605
13 Gasket(between tunnel and motor bracket) 70 1313
14 O-ring seals in motor bracket 70 1302
15 Lower motor bracket 70 0502
16 Upper motor bracket w/bolts 70 0503
17 Motor bolt 110009
18 Motor bolt washer 50 1181
19 Motor bolt spring washer 115003
20 Oil hose with hose clamps 20 0400
21 Oil container with bracket 20 0300
22 Complete flexible coupling
22a Gear motor, G70 70 1462
22b Gear motor, G75 70 1462
22c Gear motor, G80 70 1462
22d Bent axis piston motor, BA60 70 1465
22e Bent axis piston motor, BA75 70 1465
22f Bent axis piston motor, BA80 70 1466
22g Bent axis piston motor, BA90 70 1465
22h Bent axis piston motor, BA110 70 1464
22i Bent axis piston motor, BA125 70 1464
23 Port flange kit: (Separately from motor)
23a Gear motor, G70 n/a
23b Gear motor, G75 n/a
23c Gear motor, G80 n/a
23d Bent axis piston motor, BA60 FL-6000-34-UNC
23e Bent axis piston motor, BA75 FL-6000-1-UNC
23f Bent axis piston motor, BA80 FL-6000-1-UNC
23g Bent axis piston motor, BA90 FL-6000-1-UNC
23h Bent axis piston motor, BA110 FL-6000-114-UNC
23i Bent axis piston motor, BA125 FL-6000-114-UNC
24 Hyd. Motor assembly options:
24a Gear motor, G70 72100/G-70
24b Gear motor, G75 72100/G-75
24c Gear motor, G80 72100/G-80
24d Bent axis piston motor, BA60 72100/BA60
24e Bent axis piston motor, BA75 72100/BA75
24f Bent axis piston motor, BA80 72100/F12-080-C4C17
24g Bent axis piston motor, BA90 72100/AA2FM-090-C14
24h Bent axis piston motor, BA110 72100/F12-110-D4D13
24i Bent axis piston motor, BA125 72100/AA2FM-125-D13

The installer alone has responsibility for the installation of the spare parts. Side-Power only warranty the spare parts supplied only.

The information given in the document was correct at the time it was published. However, Sleipner Motor AS can not accept liability for any inaccuracies or omissions it may contain. Continuous product improvement may change the product specifications without notice. Therefore, Sleipner Motor AS can not accept liability for any possible differences between product and document.

File Type Language Download
DNV/GL Type Approval ø300mm/ø 412mm/ø513mm/ø610mm thruster.pdf Product sheet English  Download
Product specification sheet SH thrusters.pdf Product sheet English  Download
(INSTALLATION MANUAL) (SH) (1000, 1400).pdf Manual English  Download
(USER MANUAL) (SH).pdf Manual English  Download
CAD-files & technical drawings

3D models & technical drawings
for industry professionals

At Sleipner, we have shared our knowledge and technology with naval architects and boat builders for over a century. Now, we have also decided to open up our complete library of .cad, .igs, .dwg, .dxf, .stp, .xt, .pdf files and more.

Get access to 1000+ CAD files

Related products and categories